- 产品描述
- 产品组分
- 文件资源
- 营销中心
- 注意事项
- FAQ
- 文献追踪
-
For general laboratory use.
Shipping: shipped at ambient temperature
Storage Conditions: store at 4 °C
Short term exposure (up to 1 week cumulative) to ambient temperature possible.Shelf Life: 12 months after date of delivery
Description:
The CuAAC Cell Reaction Buffer Kit (THPTA based) is suitable to perform Copper (Cu(I))-catalyzed Azide-Alkyne Click chemistry reactions (CuAAC) with cells containing metabolically functionalized Alkyne- or Azide modified biomolecules.1 Kit provides sufficient amounts to perform 50 CuAAC experiments à 500 μl using 2 mM CuSO4 (copper source), 10 mM THPTA (Cu(I)-stabilizing ligand) and 100 mM Na-Ascorbate (reduction reagent) in 100 mM Na-Phosphate reaction buffer.
Content:
Copper source:
2 x 10 mg CuSO4 (M = 159.6 g/mol), #CLK-MI004)Cu(I) stabilizing ligand:
5 x 25 mg THPTA (M= 434.5 g/mol, #CLK-1010)Reduction Reagent:
4 x 200 mg Na-Ascorbate (M = 198.1 g/mol, #CLK-MI005)Reaction Buffer:
2 x 30 ml 100 mM Na-Phosphate Buffer, pH 710 ml ddH2O
Materials required but not provided:
Alkyne-or Azide-functionalized substrates e.g. fixed and permeabilized cells containing metabolically functionalized Alkyne- or Azide-modified biomolecules.
(Picolyl)-Azide or Alkyne detection reagent and appropriate solvent (e.g. DMSO)
For labeling of fixed and permeabilized cells:
Washing solutions e.g. PBS containing 3% BSA
Fixation solution e.g. PBS containing 3.7% formaldehyd
Permeabilization solution e.g. PBS containing 0.5% Triton X-100
Mounting medium for imaging
Additional labeling reagent such as nuclear stain or antibody1. Introduction
Copper (Cu(I))-catalyzed Azide-Alkyne Click chemistry reactions (CuAAC) describe the reaction of an Azide-functionalized molecule A with a terminal Alkyne-functionalized molecule B that results in a stable conjugate A-B via a Triazole moiety.Since terminal Alkynes are fairly unreactive towards Azides, the efficiency of CuAAC reactions strongly depends on the presence of a metal catalyst such as copper ions in the +1 oxidation state (Cu(I)).
Different copper sources, reduction reagents and Cu(I) stabilizing ligands are available however, for most bioconjugation applications the combination of the Cu(II) salt CuSO4 as copper source, a water-soluble Cu(I) stabilizing ligand such as BTTAA and sodium ascorbate as a reduction reagent is recommended.[1-3]
The use of Picolyl-Azide reagents instead of conventional Azide reagents can further increase the reaction efficiency and decrease the required final CuSO4 concentration due to the internal copper chelating moiety.[4]The set-up of a CuAAC reaction is based on the following general three-step procedure:
- Prepare a mix of Alkyne- and Azide functionalized molecules in an appropriate reaction buffer.
- Prepare a CuSO4: Cu(I)-ligand premix, add it to the Azide- Alkyne solution and mix briefly.
- Add Na-Ascorbate as reduction reagent at last to start the reaction.
The CuAAC Cell Reaction Buffer Kit (THPTA based) provides sufficient amounts to perform 50 CuAAC experiments à 500 μl using 2 mM CuSO4, 10 mM THPTA and 100 mM Na-Ascorbate in 100 mM Na-Phosphate reaction buffer.
A general protocol for labeling of fixed and permeabilized cells containing metabolically functionalized Alkyne- or Azide-modified biomolecules is outlined below (see 3.) however, individual optimization might be required for different CUAAC labeling experiments as well as for critical reaction parameter e.g. final CuSO4 concentration, CuSO4:THPTA ratio, detection reagent concentration.
Hong et al.[2] and Presolski et al.[1] provide useful background information on the influence of CuSO4 concentration, CuSO4: ligand ratio and reaction buffer type that may be used as a starting point if optimization is required.
2. Preparation of stock solutions
The concentration of stock solutions (2.1 to 2.3) is suitable to prepare 500 μl assays containing 2 mM CuSO4, 10 mM THPTA and 100 mM Na-Ascorbate (see 3.3 and 3.4, respectively). Adjustments might be required if different assay volumes or final compound concentrations are used.
2.1 THPTA stock solution (Cu(I) stabilizing ligand)
- Add an appropriate amount of ddH2O (Tab. 1), vortex until the compound is completely dissolved and spin down briefly.
- Prepare aliquots to avoid repeated freeze-thaw-cycles and store at -20 °C.
- The solution is stable up to 1 year at -20 °C.
Table 1 Volume of ddH2O required for a 250 mM THPTA stock solution.
THPTA Concentration of stock solution Amount of ddH2O 25 mg 250 mM 230 μl 2.2 CuSO4 stock solution (copper source)
- Add an appropriate amount of ddH2O (Tab. 2), vortex until the compound is completely dissolved and spin down briefly.
- Prepare aliquots to avoid repeated freeze-thaw-cycles and store at -20 °C.
- The solution is stable up to 1 year at -20 °C.
Table 2 Volume of ddH2O required for a 100 mM CuSO4 stock solution.
CuSO4 Concentration of stock solution Amount of ddH2O 10 mg 100 mM 628 μl 2.3 Na-Ascorbate stock solution (reduction reagent)
- Add an appropriate amount of ddH2O (Tab. 3), vortex until the compound is completely dissolved and spin down briefly.
- Prepare aliquots to avoid repeated freeze-thaw-cycles and store at -20 °C.
- The solution is stable up to 1 year at -20 °C.
Please note: Do not use solutions that appear brown. Freshly prepared, fully functional Na-Ascorbate solutions are colorless to slightly yellow and turn brown upon oxidization thereby losing their reduction capability.
Table 3 Volume of ddH2O required for a 1 M Na-Ascorbate stock solution.
Na-Ascorbate Concentration of stock solution Amount of ddH2O 200 mg 1 M 1010 μl 2.4 (Picolyl)-Azide detection reagent stock solution
- (Picolyl)-Azide detection reagents are not provided within this kit.
- Add an appropriate amount of suitable solvent e.g. DMSO to achieve a stock solution concentration of 10 mM for Azide detection reagents and 500 μM for Picolyl-Azide detection reagents.
- Final concentrations of Azide or Alkyne detection reagents may range from 2 μM to 100 μM. Final concentrations of Picolyl-Azide detection reagents may range from 0.5 to 5 μM (see 3.4).
3. General protocol for CLICK labeling of fixated and permeabilized cells containing metabolically functionalized Alkyne- or Azide-modified biomolecules
The protocol below is intended as a general guideline however, individual optimization might be required.
3.1 Metabolically label cells with an Alkyne or Azide-functionalized substrate
- Cultivate cells on coverslips under conditions that ensure optimal growth of cell type.
- Add Alkyne- or Azide-functionalized substrate at the desired final concentration and cultivate for an appropriate time under conditions optimal for metabolic incorporation of the modified substrate.
3.2 Fixate and permeabilize cells
Please note: The fixation with 3.7% formaldehyde in PBS and subsequent permeabilization with 0.5% Triton X-100 is a general guideline. Optimization might be required. Different reagent concentrations, different fixation and permeabilization reagents (e.g. methanol or saponin) or TBS as buffer solution intstead of PBS can be used as well. Permeabilization is not required for cell surface or lipid component labeling.
- Remove cultivation medium
- Transfer each coverslip to a well of a 6-well plate
- Add 1 ml of 3.7% formaldehyde in PBS for fixation and incubate for 15 min. at room temperature.
- Remove fixation reagent and wash 2-3 times with PBS containing 3% BSA.
- Add 1 ml of Triton X-100 in PBS and incubate for 20 minutes at room temperature for permeabilization.
3.3 Prepare CuSO4:THPTA-Premix
Please note: Both the final CuSO4 concentration as well as CuSO4:THPTA ratio are critical parameters for CuAAC reaction efficiency. A final CuSO4 concentration of 2 mM and a CuSO4:THPTA ratio of 1:5 is recommended as a starting point for labeling of fixed and permeabilized cells containing metabolically Azide- or Alkyne-functionalized biomolecules. Individual optimization for each assay is strongly recommended. Minimum CuSO4 concentration: 50 μM.
- Prepare the CuSO4:THPTA-Premix freshly for each experiment.
- Allow all solutions to warm up to room temperature.
- Mix the appropriate amount of 100 mM CuSO4 and 250 mM THPTA stock solution (Tab. 4) by vortexing and spin down briefly.
- 30 μl CuSO4:THPTA-Premix (1 Assay) is sufficient for the preparation of 500 μl CLICK reaction cocktail (see. 3.4).
Table 4 Pipetting scheme for CuSO4:THPTA-Premix (ratio 1:5).
Compound Final conc. 1 Assay 10 Assays 100 mM CuSO4 stock solution (see 2.2) 33.33 mM 10 μl 100 μl 250 mM THPTA stock solution (see 2.1) 166.66 mM 20 μl 200 μl 3.4 Prepare CLICK reaction cocktail
Please note: Prepare CLICK reaction cocktail freshly for each experiment and use it immediately but definitely within 15 minutes after preparation. 500 μl CLICK reaction cocktail (1 Assay) is sufficient to label one 18x18 coverslip.
- Allow all solutions to warm up to room temperature.
- Refer to Tab. 5 for appropriate amounts of compound stock solutions.
- 500 μl CLICK reaction cocktail (1 Assay) is sufficient for a 18x18 coverslip.
- Add an appropriate amount of Azide- or Alkyne detection reagent solution to the reaction buffer, vortex and spin-down briefly.
- Add CuSO4/THPTA Premix, vortex and spin down briefly.
- Add Na-Ascorbate, vortex and spin down briefly.
Table 5 Pipetting scheme for CLICK reaction cocktail. Please add the compounds exactly in the order described below.
Compound Final conc. 1 Assay (500 μl) 10 Assays (5 ml) 100 mM Na-Phosphate reaction buffer, pH 7 419 μl 4.19 ml 10 mM Azide or-Alkyne detection reagent stock solution (not provided, see 2.4) 20 μM[1] 1 μl 10 μl 33.33 mM / 166.66 mM CuSO4:THPTA-Premix (see 3.3) 2 mM / 10 mM 30 μl 300 μl 1 M Na-Ascorbate stock solution (see 2.3) 100 mM 50 μl 500 μl [1]Final concentrations of Azide or Alkyne detection reagents may range from 2 μM to 100 μM. Final concentrations of Picolyl-Azide detection reagents may range from 0.5 to 5 μM. We recommend starting with 20 μM or 5 μM, respectively. Concentrations can be titrated down in case of high background or up in case of low signal.
3.5 Perform CLICK labeling of fixated and permeabilized Alkyne- or Azide-labeled cells
- Remove the permeabilization buffer (see 3.2) and wash 2-3 times with PBS containing 3% BSA.
- Add 500 μl CLICK reaction cocktail (see 3.4) to each well containing one coverslip. Ensure that the coverslip is entirely covered with solution.
- Incubate samples 30 – 60 min at room temperature (protected from light).
- Remove CLICK reaction cocktail and wash cells 1-2 times with PBS containing 3% BSA.
- Remove wash solution.
- For nuclear staining with DAPI or Hoechst 33342 or antibody labeling wash once with PBS, remove PBS and proceed with staining according to the manufacturer’s protocol.
-
产品组分
内容 型号
规格 储存温度
CuAAC细胞反应缓冲液试剂盒(THPTA)
CNCLK074-01 50次
-20°C CuAAC细胞反应缓冲液试剂盒(THPTA)
CNCLK074-02 100次
-20°C 操作手册
1 1 常温
-
营销中心
-
注意事项
保存建议 厂家推荐蓝冰运输。当您收到产品后，按照说明书建议保存于-20°C。 -
FAQ
-
Selected References:
[1] Presolski et al. (2011) Copper-Catalyzed Azide-Alkyne Click Chemistry for Bioconjugation. Current Protocols in Chemical Biology 3:153.
[2] Hong et al. (2011) Analysis and Optimization of Copper-Catalyzed Azide-Alkyne Cycloaddition for Bioconjugation. Angew. Chem. Int. Ed. 48:9879.
[3] Besanceney-Webler et al. (2011) Increasing the Efficiacy of Bioorthogonal Click Reactions for Bioconjugation: A Comparative Study. Angew. Chem. Int. Ed. 50:8051.
[4] Uttamapinant et al. (2012) Fast, Cell-Compatible Click Chemistry with Copper-Chelating Azides for Biomolecular Labeling. Angew. Chem. Int. Ed. 51:5852.PERK-dependent reciprocal crosstalk between ER and non-centrosomal microtubules coordinates ER architecture and cell shape
Miguel Sánchez-Álvarez, Fidel Nicolás Lolo, ..., Chris Bakal
Cell Reports | 2025 May 27 | 40267909
Il-6 signaling exacerbates hallmarks of chronic tendon disease by stimulating reparative fibroblasts
Tino Stauber, Greta Moschini, ..., Hiroshi Takayanagi
eLife | 2025 Feb 07 | 39918402
Randomly incorporated genomic N6-methyldeoxyadenosine delays zygotic transcription initiation in a cnidarian.
Febrimarsa, Sebastian G Gornik, ..., Uri Frank
The EMBO Journal | 2023 Sep 18 | 37708295
Randomly incorporated genomic 6mA delays zygotic transcription initiation
Febrimarsa, Gornik Sebastian G, ..., Frank Uri
bioRxiv | 2022 Oct 27
在线留言
如果您对我们的产品感兴趣，请留下您的信息，我们将尽快与您联系，谢谢！
艾维缔官网
艾德官网
B站IVDSHOW
抖音军哥聊表观
视频号艾维缔
小红书艾维缔
快手表观盒子
表观遗传学
联系我们
